wavesharelib/Arduino/epd5in83/epd5in83.cpp

/**
 *  @filename   :   epd5in83.h
 *  @brief      :   Header file for e-paper library epd5in83.cpp
 *  @author     :   MyMX from Waveshare
 *  
 *  Copyright (C) Waveshare     April 6 2018
 *
 * Permission is hereby granted, free of charge, to any person obtaining a copy
 * of this software and associated documnetation files (the "Software"), to deal
 * in the Software without restriction, including without limitation the rights
 * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
 * copies of the Software, and to permit persons to  whom the Software is
 * furished to do so, subject to the following conditions:
 *
 * The above copyright notice and this permission notice shall be included in
 * all copies or substantial portions of the Software.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
 * FITNESS OR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
 * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
 * LIABILITY WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
 * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
 * THE SOFTWARE.
 */

#include <stdlib.h>
#include "epd5in83.h"

Epd::~Epd() {
};

Epd::Epd() {
    reset_pin = RST_PIN;
    dc_pin = DC_PIN;
    cs_pin = CS_PIN;
    busy_pin = BUSY_PIN;
    width = EPD_WIDTH;
    height = EPD_HEIGHT;
};

int Epd::Init(void) {
    if (IfInit() != 0) {
        return -1;
    }
    Reset();

    SendCommand(POWER_SETTING); 
    SendData(0x37);
    SendData(0x00);

    SendCommand(PANEL_SETTING);
    SendData(0xCF);
    SendData(0x08);
    
    SendCommand(BOOSTER_SOFT_START);
    SendData(0xc7);     
    SendData(0xcc);
    SendData(0x28);

    SendCommand(POWER_ON);
    WaitUntilIdle();

    SendCommand(PLL_CONTROL);
    SendData(0x3c);        

    SendCommand(TEMPERATURE_CALIBRATION);
    SendData(0x00);

    SendCommand(VCOM_AND_DATA_INTERVAL_SETTING);
    SendData(0x77);

    SendCommand(TCON_SETTING);
    SendData(0x22);

    SendCommand(TCON_RESOLUTION);
    SendData(width >> 8);     //source 640
    SendData(width & 0xff);
    SendData(height >> 8);     //gate 384
    SendData(height & 0xff);

    SendCommand(VCM_DC_SETTING);
    SendData(0x1E);      //decide by LUT file

    SendCommand(0xe5);           //FLASH MODE            
    SendData(0x03);  

    return 0;
}

/**
 *  @brief: basic function for sending commands
 */
void Epd::SendCommand(unsigned char command) {
    DigitalWrite(dc_pin, LOW);
    SpiTransfer(command);
}

/**
 *  @brief: basic function for sending data
 */
void Epd::SendData(unsigned char data) {
    DigitalWrite(dc_pin, HIGH);
    SpiTransfer(data);
}

/**
 *  @brief: Wait until the busy_pin goes HIGH
 */
void Epd::WaitUntilIdle(void) {
    while(DigitalRead(busy_pin) == 0) {      //0: busy, 1: idle
        DelayMs(100);
    }      
}

/**
 *  @brief: module reset.
 *          often used to awaken the module in deep sleep,
 *          see Epd::Sleep();
 */
void Epd::Reset(void) {
    DigitalWrite(reset_pin, LOW);                //module reset    
    DelayMs(200);
    DigitalWrite(reset_pin, HIGH);
    DelayMs(200);    
}

void Epd::DisplayFrame(const unsigned char** frame_buffer) {
    unsigned char temp1, temp2;
    SendCommand(DATA_START_TRANSMISSION_1);
    /**  
    * Size of a single array cannot be larger than 32K in AVR GCC, therefore 
    * you have to split the image data (33600 bytes in total) into 2 parts 
    */
    for (int image_data_part = 0; image_data_part < 2; image_data_part++) {
      for(long i = 0; i < width / 8 * height /2; i++) {   
          temp1 = pgm_read_byte(frame_buffer[image_data_part] + i);
          for(unsigned char j = 0; j < 8; j++) {
              if(temp1 & 0x80)
                  temp2 = 0x03;
              else
                  temp2 = 0x00;
              
              temp2 <<= 4;
              temp1 <<= 1;
              j++;
              if(temp1 & 0x80)
                  temp2 |= 0x03;
              else
                  temp2 |= 0x00;
              temp1 <<= 1;
              SendData(temp2); 
          }
      }
    }
    SendCommand(DISPLAY_REFRESH);
    DelayMs(100);
    WaitUntilIdle();
}

/**
 *  @brief: After this command is transmitted, the chip would enter the 
 *          deep-sleep mode to save power. 
 *          The deep sleep mode would return to standby by hardware reset. 
 *          The only one parameter is a check code, the command would be
 *          executed if check code = 0xA5. 
 *          You can use EPD_Reset() to awaken
 */
void Epd::Sleep(void) {
    SendCommand(POWER_OFF);
    WaitUntilIdle();
    SendCommand(DEEP_SLEEP);
    SendData(0xa5);
}

/* END OF FILE */