/***************************************************************************** * | File : EPD_1in54.C * | Author : Waveshare team * | Function : 1.54inch e-paper * | Info : *---------------- * | This version: V3.0 * | Date : 2019-06-12 * | Info : * ----------------------------------------------------------------------------- * V3.0(2019-06-12): * 1.Change: * lut_full_update[] => EPD_1IN54_lut_full_update[] * lut_partial_update[] => EPD_1IN54_lut_partial_update[] * EPD_Reset() => EPD_1IN54_Reset() * EPD_SendCommand() => EPD_1IN54_SendCommand() * EPD_SendData() => EPD_1IN54_SendData() * EPD_WaitUntilIdle() => EPD_1IN54_ReadBusy() * EPD_SetLut() => EPD_1IN54_SetLut() * EPD_SetWindow() => EPD_1IN54_SetWindow() * EPD_SetCursor() => EPD_1IN54_SetCursor() * EPD_TurnOnDisplay() => EPD_1IN54_TurnOnDisplay() * EPD_Init() => EPD_1IN54_Init() * EPD_Clear() => EPD_1IN54_Clear() * EPD_Display() => EPD_1IN54_Display() * EPD_Sleep() => EPD_1IN54_Sleep() * 2.remove commands define: * #define PANEL_SETTING 0x00 * #define POWER_SETTING 0x01 * #define POWER_OFF 0x02 * #define POWER_OFF_SEQUENCE_SETTING 0x03 * #define POWER_ON 0x04 * #define POWER_ON_MEASURE 0x05 * #define BOOSTER_SOFT_START 0x06 * #define DEEP_SLEEP 0x07 * #define DATA_START_TRANSMISSION_1 0x10 * #define DATA_STOP 0x11 * #define DISPLAY_REFRESH 0x12 * #define DATA_START_TRANSMISSION_2 0x13 * #define PLL_CONTROL 0x30 * #define TEMPERATURE_SENSOR_COMMAND 0x40 * #define TEMPERATURE_SENSOR_CALIBRATION 0x41 * #define TEMPERATURE_SENSOR_WRITE 0x42 * #define TEMPERATURE_SENSOR_READ 0x43 * #define VCOM_AND_DATA_INTERVAL_SETTING 0x50 * #define LOW_POWER_DETECTION 0x51 * #define TCON_SETTING 0x60 * #define TCON_RESOLUTION 0x61 * #define SOURCE_AND_GATE_START_SETTING 0x62 * #define GET_STATUS 0x71 * #define AUTO_MEASURE_VCOM 0x80 * #define VCOM_VALUE 0x81 * #define VCM_DC_SETTING_REGISTER 0x82 * #define PROGRAM_MODE 0xA0 * #define ACTIVE_PROGRAM 0xA1 * #define READ_OTP_DATA 0xA2 * ----------------------------------------------------------------------------- * V2.0(2018-10-30): * 1.Remove:ImageBuff[EPD_1IN54_HEIGHT * EPD_1IN54_WIDTH / 8] * 2.Change:EPD_Display(UBYTE *Image) * Need to pass parameters: pointer to cached data * 3.Change: * EPD_RST -> EPD_RST_PIN * EPD_DC -> EPD_DC_PIN * EPD_CS -> EPD_CS_PIN * EPD_BUSY -> EPD_BUSY_PIN # # Permission is hereby granted, free of charge, to any person obtaining a copy # of this software and associated documnetation files (the "Software"), to deal # in the Software without restriction, including without limitation the rights # to use, copy, modify, merge, publish, distribute, sublicense, and/or sell # copies of the Software, and to permit persons to whom the Software is # furished to do so, subject to the following conditions: # # The above copyright notice and this permission notice shall be included in # all copies or substantial portions of the Software. # # THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR # IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, # FITNESS OR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE # AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER # LIABILITY WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, # OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN # THE SOFTWARE. # ******************************************************************************/ #include "EPD_1in54.h" #include "Debug.h" static const unsigned char EPD_1IN54_lut_full_update[] = { 0x02, 0x02, 0x01, 0x11, 0x12, 0x12, 0x22, 0x22, 0x66, 0x69, 0x69, 0x59, 0x58, 0x99, 0x99, 0x88, 0x00, 0x00, 0x00, 0x00, 0xF8, 0xB4, 0x13, 0x51, 0x35, 0x51, 0x51, 0x19, 0x01, 0x00 }; static const unsigned char EPD_1IN54_lut_partial_update[] = { 0x10, 0x18, 0x18, 0x08, 0x18, 0x18, 0x08, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x13, 0x14, 0x44, 0x12, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }; /****************************************************************************** function : Software reset parameter: ******************************************************************************/ static void EPD_1IN54_Reset(void) { DEV_Digital_Write(EPD_RST_PIN, 1); DEV_Delay_ms(200); DEV_Digital_Write(EPD_RST_PIN, 0); DEV_Delay_ms(2); DEV_Digital_Write(EPD_RST_PIN, 1); DEV_Delay_ms(200); } /****************************************************************************** function : send command parameter: Reg : Command register ******************************************************************************/ static void EPD_1IN54_SendCommand(UBYTE Reg) { DEV_Digital_Write(EPD_DC_PIN, 0); DEV_Digital_Write(EPD_CS_PIN, 0); DEV_SPI_WriteByte(Reg); DEV_Digital_Write(EPD_CS_PIN, 1); } /****************************************************************************** function : send data parameter: Data : Write data ******************************************************************************/ static void EPD_1IN54_SendData(UBYTE Data) { DEV_Digital_Write(EPD_DC_PIN, 1); DEV_Digital_Write(EPD_CS_PIN, 0); DEV_SPI_WriteByte(Data); DEV_Digital_Write(EPD_CS_PIN, 1); } /****************************************************************************** function : Wait until the busy_pin goes LOW parameter: ******************************************************************************/ void EPD_1IN54_ReadBusy(void) { Debug("e-Paper busy\r\n"); while(DEV_Digital_Read(EPD_BUSY_PIN) == 1) { //LOW: idle, HIGH: busy DEV_Delay_ms(100); } Debug("e-Paper busy release\r\n"); } /****************************************************************************** function : Setting the display window parameter: ******************************************************************************/ static void EPD_1IN54_SetWindow(UWORD Xstart, UWORD Ystart, UWORD Xend, UWORD Yend) { EPD_1IN54_SendCommand(0x44); // SET_RAM_X_ADDRESS_START_END_POSITION EPD_1IN54_SendData((Xstart >> 3) & 0xFF); EPD_1IN54_SendData((Xend >> 3) & 0xFF); EPD_1IN54_SendCommand(0x45); // SET_RAM_Y_ADDRESS_START_END_POSITION EPD_1IN54_SendData(Ystart & 0xFF); EPD_1IN54_SendData((Ystart >> 8) & 0xFF); EPD_1IN54_SendData(Yend & 0xFF); EPD_1IN54_SendData((Yend >> 8) & 0xFF); } /****************************************************************************** function : Set Cursor parameter: ******************************************************************************/ static void EPD_1IN54_SetCursor(UWORD Xstart, UWORD Ystart) { EPD_1IN54_SendCommand(0x4E); // SET_RAM_X_ADDRESS_COUNTER EPD_1IN54_SendData((Xstart >> 3) & 0xFF); EPD_1IN54_SendCommand(0x4F); // SET_RAM_Y_ADDRESS_COUNTER EPD_1IN54_SendData(Ystart & 0xFF); EPD_1IN54_SendData((Ystart >> 8) & 0xFF); } /****************************************************************************** function : Turn On Display parameter: ******************************************************************************/ static void EPD_1IN54_TurnOnDisplay(void) { EPD_1IN54_SendCommand(0x22); // DISPLAY_UPDATE_CONTROL_2 EPD_1IN54_SendData(0xC4); EPD_1IN54_SendCommand(0x20); // MASTER_ACTIVATION EPD_1IN54_SendCommand(0xFF); // TERMINATE_FRAME_READ_WRITE EPD_1IN54_ReadBusy(); } /****************************************************************************** function : Initialize the e-Paper register parameter: ******************************************************************************/ void EPD_1IN54_Init(UBYTE Mode) { EPD_1IN54_Reset(); EPD_1IN54_SendCommand(0x01); // DRIVER_OUTPUT_CONTROL EPD_1IN54_SendData((EPD_1IN54_HEIGHT - 1) & 0xFF); EPD_1IN54_SendData(((EPD_1IN54_HEIGHT - 1) >> 8) & 0xFF); EPD_1IN54_SendData(0x00); // GD = 0; SM = 0; TB = 0; EPD_1IN54_SendCommand(0x0C); // BOOSTER_SOFT_START_CONTROL EPD_1IN54_SendData(0xD7); EPD_1IN54_SendData(0xD6); EPD_1IN54_SendData(0x9D); EPD_1IN54_SendCommand(0x2C); // WRITE_VCOM_REGISTER EPD_1IN54_SendData(0xA8); // VCOM 7C EPD_1IN54_SendCommand(0x3A); // SET_DUMMY_LINE_PERIOD EPD_1IN54_SendData(0x1A); // 4 dummy lines per gate EPD_1IN54_SendCommand(0x3B); // SET_GATE_TIME EPD_1IN54_SendData(0x08); // 2us per line EPD_1IN54_SendCommand(0x11); EPD_1IN54_SendData(0x03); //set the look-up table register EPD_1IN54_SendCommand(0x32); if(Mode == EPD_1IN54_FULL){ for (UWORD i = 0; i < 30; i++) { EPD_1IN54_SendData(EPD_1IN54_lut_full_update[i]); } }else if(Mode == EPD_1IN54_PART){ for (UWORD i = 0; i < 30; i++) { EPD_1IN54_SendData(EPD_1IN54_lut_partial_update[i]); } }else{ Debug("error, the Mode is EPD_1IN54_FULL or EPD_1IN54_PART"); } } /****************************************************************************** function : Clear screen parameter: ******************************************************************************/ void EPD_1IN54_Clear(void) { UWORD Width, Height; Width = (EPD_1IN54_WIDTH % 8 == 0)? (EPD_1IN54_WIDTH / 8 ): (EPD_1IN54_WIDTH / 8 + 1); Height = EPD_1IN54_HEIGHT; EPD_1IN54_SetWindow(0, 0, EPD_1IN54_WIDTH, EPD_1IN54_HEIGHT); for (UWORD j = 0; j < Height; j++) { EPD_1IN54_SetCursor(0, j); EPD_1IN54_SendCommand(0x24); for (UWORD i = 0; i < Width; i++) { EPD_1IN54_SendData(0XFF); } } EPD_1IN54_TurnOnDisplay(); } /****************************************************************************** function : Sends the image buffer in RAM to e-Paper and displays parameter: ******************************************************************************/ void EPD_1IN54_Display(UBYTE *Image) { UWORD Width, Height; Width = (EPD_1IN54_WIDTH % 8 == 0)? (EPD_1IN54_WIDTH / 8 ): (EPD_1IN54_WIDTH / 8 + 1); Height = EPD_1IN54_HEIGHT; UDOUBLE Addr = 0; // UDOUBLE Offset = ImageName; EPD_1IN54_SetWindow(0, 0, EPD_1IN54_WIDTH, EPD_1IN54_HEIGHT); for (UWORD j = 0; j < Height; j++) { EPD_1IN54_SetCursor(0, j); EPD_1IN54_SendCommand(0x24); for (UWORD i = 0; i < Width; i++) { Addr = i + j * Width; EPD_1IN54_SendData(Image[Addr]); } } EPD_1IN54_TurnOnDisplay(); } /****************************************************************************** function : Enter sleep mode parameter: ******************************************************************************/ void EPD_1IN54_Sleep(void) { EPD_1IN54_SendCommand(0x10); EPD_1IN54_SendData(0x01); }